DI with selectable pre/post operation. — 18-volt operation via batteries, phantom power or optional power supply. Owner's Manual. Manual Version 3.1 ... 1. Plug in your instrument, the TONE HAMMER, and your amplifier. With MASTER volume down, bring the GAIN control to 12 o'clock. 2. Turn on your amplifier and ...

This manual describes the operation and programming of the Jester lighting desk . It begins with a general description of the desk, the master controls, turning on the .... 1 second. The PRESET light next to the MODE button will come on. 2. Ensure the bottom bank of faders are set to 1-12(24) mode and the FADE TIME.

PHOBOS - USER MANUAL. YOUR FIRST 'TOUR'. SOUND SOURCES 1,2,3,4. CONVOLVERS W,X,Y. CONVOLUTION TRIANGLE. MASTER CONTROLS & KEYBOARD RANGE. To give a simple intro into the world of Phobos, it starts at the. Sources, which are triggered depending on their individual Key- board Range, get ...

Mar 24, 2011 ... 1. Read Me. Eleven Rack Expansion Pack (Firmware 2.0.1). New Features, Upgrade Info, and Known Issues. This document describes the new amps, .... Master Controls master volume output. ..... install, you must both update the software on your computer, and update the firmware on your Eleven Rack.

PAGE 7. UCO - USER MANUAL. THE 'GENERAL OVERVIEW' PANEL. 1. STOP SWITCHER. These are the stops, they are active (or “out”) when highlighted and any numer of stops .... EXPRESSION - CC#11 Displays the overall instrument vol - ume (0-100%). Remember you can also trim your instrument volume with CC#7.

This product is warranted to be free from defects in materials or workmanship for period of one year from the date of purchase by the original owner. To ensure a high level of performance and reliability for which this equipment has been designed and manufactured, read this User Guide before operating. In the event of a ...

NOTE: For the MARK II-C+ Aficionado–Re: Channels 2 & 3; We have, in both Channels 2 and 3 of the JP-2C, removed the VOL-. UME 1 Control and the LEAD MASTER control from the Panel Layout as compared to the LEAD Mode of the original MARK II-C+ in favor of user simplicity. The LEAD MASTER is a largely ...

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not ... Follow all installation instructions. Failure to follow instructions ..... MONI MASTER controls are turned down. 1 Connect cables to your ...

Install the MicroSmart AS-Interface master module according to the instructions described in this user's manual. Improper installation will result ..... AS-Interface Master Module. Power Consumption. 540 mW (24V DC). Weight. 85g. Maximum Bus Cycle. When 1 through 19 slaves are connected: 3 msec. When 20 through 62 ...

gages the on-board reverb, effects loop and secondary master volume with channel-assigning switches for all three ... instructions in the user manual accompanying ... 1. READ INSTRUCTIONS – All the safety and operating instructions should be read before this product is operated. 2. RETAIN INSTRUCTIONS – The safety.

EMX62M. 1. The Owner's Manual. Revisions. Thank you for purchasing the Yamaha EMX62M Powered. Mixer. Parts of the EMX62M owner's manual have been revised. ..... Doing so may cause oscillation depending on the condition of the connected unit and speakers, and may damage the speakers. Operation. Installation.

Wheatstone could void the user's authority to operate this equipment. Page 4. READ ME! Aug 2013. Attention! Important Safety Instructions. PSE-2 Power Supply. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all ... Wheatstone WheatNet‑IP Navigator program (aka the Navigator. GUI).

Transmitting MIDI Program Change commands ... The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user ... 1. Read Instructions - All thesafety andoperating instructions should be read before the appliance is operated. 2. Retain Instructions - The safety and operating instructions.

Register Description. The SPI master controls the MAX3420E by reading and writing 21 registers (Table 1). For a complete description of register contents, please refer to the “MAX3420E. Programming Guide.” A register access consists of the. SPI master first writing an SPI command byte, followed by reading or writing the ...

This way, Iris 1 will always be able to find and open its original presets . The Iris 1 'Sub' section used samples from our Moog Modular library . If you have Iris 1 patches that are .... when you open, offering you links to this user manual and videos online that can help you get started . .... The Preview volume corresponds.

cables. Cable/s supplied with this prod- uct MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use ..... VOLUME. USB/AUX OUTPUT. VOLUME. USB (THR Guitar DI 1, 2). Compressor. Reverb. Delay. Effect. Noise Gate. Amp. Simulation. *THR10/10C/ 10X only.

however, we recommend that you read this operating manual thoroughly before use. ..... sent to the LlR STEREO program buss. Rated output ... Foldback Out, Echo Send and Stereo Out Sections o FB master controls. The FB 1 and FB 2 master controls control the overall level of the mix on the respec tive FB busses to be ...

EastWest/Quantum Leap. Symphonic Choirs. Virtual Instrument. Original Edition and Gold Edition. Users' Manual ..... The EWQL Symphonic Choirs User Interface. 19 Important Note for the “Multi” Choirs. 19 Master Controls. 21 Microphones Controls. 23 Performance Controls. 24 Stereo Double Controls. 24 Reverb Master.

program in 1914, the Time Equipment Division of the company had a fairly complete line of ... This recorder was manually wound, with manual printing of time .... [See page 8 of our online exhibit —They Also Served: An Album of IBM Special Products, Vol. 1“ available on the Internet at http://www.ibm.com/history for an ...

Full master controls: monitor, volume, effects send, ... VOLUME. Allows individual setting of channel input for desired signal mix. If setting is consistently low (1 or 2) , or high (8 to lo), adjust INPUT. ATTEN. Inputs: .... When completed perform a lhstenlng test uslng program materlal s~mllar to the planned performance.